Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

 1 in stock

Motobatt quadflex 30Ah battery. Quadflex technology means you have two positive and two negative threaded terminals allowing maximum flexibility when installing. This powerful battery produces a massive 390 cranking amps, and is rated at 32 ah.

These sealed absorbed glass matt batteries have been used in military and off road applications for many years.
They offer increased lifespan, higher vibration resistance and electrical performance. This battery is also leak, vibration and spill proof if installed correctly.
Supplied fully charged and ready to fit.

NB This battery must not be trickle charged or charged using a traditional manual charger, AGM batteries require a smart charger - we recommend ACA96000
For more information on charging AGM batteries see these FAQ's.

This is a better value replacement for the Odyssey PC925 battery. Replaces Guzzi refs. 14704550, 18704550, 28704550, 28704545, 28704551, 28704552, 14704551, 14704500 and 14704505

One year warranty on all our Motobatt batteries.

Slightly taller than original loop frame battery so you may need to make some modification to retaining bracket

Please note this part CANNOT be posted outside of the UK mainland area

 1 in stock

03704540-z 03704540 GU03704540 03 70 45 40
 0370 4540 0370.4540 03.70.45.40

Five piece decal set, gold lettering. Three larger decals, two smaller decals

 1 in stock

Oil seal used for crankcase on Nuovo Falcone and front wheel bearing seal on loop frame models

 1 in stock

 90403253 GU90403253 90 40 32 53
 9040 3253 9040.3253 90.40.32.53

The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.

Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping! This banjo bolt can be used in place of a standard fine thread M10 banjo bolt. Supplied with crush washers. We recommend fitting one of these brake valves per caliper
The innovative stahlbus vent valve allows you to change the brake fluid easily and without help. Clean, totally safe and fast !
This auto bleed valve combines all these advantages:

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÜV Rheinland.
  See BRA41652 for bleed valve cover

   1 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Chrome bar end mirror with a large round head and adjustable arm. Fits all models with open ended (i.e. not threaded) 7/8 inch steel handlebars.

Can be fitted on either left or right hand side of handlebars. Shown here fitted to a handlebar which is not included

 1 in stock

Universal hydraulic brakelight switch. This hydraulic switch replaces discontinued brake light switches by bolting in place of a double banjo bolt on the handlebar or rear brake master cylinder

Especially suitable for replacing the standard switch on models where the front brakes have been 'de-linked'

 1 in stock

Lightweight M20 gearbox and drive box filler plug (big twins), drive box level plug (small twins). An aluminium filler plug made in Italy.

 1 in stock

 12022600 GU12022600 12 02 26 00
 1202 2600 1202.2600 12.02.26.00

Premium softstyle light grey T-shirt printed with our original Moto Guzzi Cententary design. Celebrating 100 years of Moto Guzzi this design celebrates some of the big names behind the first century of the eagle

Printed on the same premium softstyle shirt as our classic eagle T shirt.

Sizing:

• S fits 34 - 36" chest
• M fits 38 - 40" chest
• L fits 42 - 44" chest
• XL fits 46 - 48" chest
• XXL fits 50 - 52" chest

 1 in stock

Thick protective tank cover for your workshop. Ideal for preventing expensive damage to your motorcycle tank when working on your bike (avoid brake fluid spills etc...) and also useful for leaving on your bike when not in use to avoid accidental scratches. Special anti-slip material on underside secures cover to your motorcycle tank when in use. Upper side is nylon for ease of cleaning.

 1 in stock